WellGate 2808
8-Port FXS mixed SIP IP Gateway

 

WellGate 2808 Front View

WellGate 2808 Rear View

 

  • Dual IP Stack : IPv6 and IPv4 Simultaneously
  • Support up to 16 SIP Trunks to register
  • Enhance existing PABX to VoIP Call
  • Consistent with WellGate 2504 and 2424S gateway
  • Flexible Routes Plan, Dial Plan, Digit Manipulation
  • Redundant Firmware Image
 

Introduction

Information

WellGate 2808 is 8-port FXS gateway with SIP protocol IP device
which connects up to 8 Lines of analog telephone set (or, analog
trunk line of legend PABX) to make or receive VoIP call over Internet
or VPN network. This device is not only suitable for legend PABX to
enable VoIP call without changing existing cabling, dial plan, and
extension number, but also work with IP-PBX and SIP Server directly.
Its design, firmware, auto provision and webpage are consistent
with WellGate 2504 (4 ports FXS) and WellGate 2424S (24 ports FXS)
gateway.


To select up to 16 SIP TRUNK Accounts

WellGate 2808 is appropriate to use 16 VoIP SIP Trunk or IP Centrex service or IP-PBX
within offices and remote branch ffices. One of 16 SIP Servers (or ITSP Service provider
or alternative IP-PBX ) can be configured freely at each line (FXS port ) to make or receive
IP Call. It provides 16 service platforms according to your dial number or routes plan.


IPv6 VoIP Gateway is ready to Market

IPv6 address was developed for years, however, it was not practical to our life up to now.
More and more electronic devices are able to link to IP Network(for instance, Internet of
Things, IoT). This makes existing IPv4 address supply in short to global market. Meanwhile,
the emerging countries are not able to increase IPv4 address supply due to strong market
demand on broadband services. WellGate 2808 is an SIP based FXS gateway which was
built-in both IPv6 and IPv4 IP address. Whenever you are ready to deploy IPv6 network,
or reserve the future expansion to IPv6 from existing IPv4 address, WellGate 2808 is ready
to grow up with you. Both IPv6 and IPv4 addresses are working simultaneously at Voice IP
Call. Its flexibility of both IPv6 and IPv4 accept and interwork both addresses on today and
tomorrow whenever you need.


Flexible Dial plan and Route Plan Features

WellGate 2808 provides flexible Dial Plan between FXS and SIP IP Trunk (SIP Soft Switch
or IP-PBX). Dial Plan is to configure in what condition the digits can be sent out to/from IP
network. The dialing inter-digit time before dialing is configurable to meet local PSTN line
or PBX’s extension line. Dial Rule is able to detect the prefix code and maximum digits
reached and then dial automatically. The Digit Manipulation (DM) allows you to configure
matched prefix code, digits length, start and stop digit position to be replaced digits as well.

Route Plan is to configure the incoming and outgoing call routes which you wanth you want
this call to go out or allow to income. For instance, IP incoming call may reach to one FXS
FXS port with Priority or Cyclic access. You can also configure IP incoming call by Matched
prefix digits, matched dialing number to FXS line and Matched digit length. From FXS outgoing
all to SIP IP routes, the hunting type supports Priority or Cyclic or Simultaneously to select
which SIP trunk ( SIP Proxy Server, or IP-PBX ) to go. FXS outgoing call routes also support
by Matched prefix digits, Matched outgoing SIP Trunk number and Matched digit length. Both
directions support No Answer time out and Backup Routes.


Upgrade existing PABX to enable VoIP call

WellGate 2808 is a SIP IP device to connect with existing PABX and enable to make or receive
VoIP call without affecting existing cabling, extension number or dial behaviors. It is an easy
and quick way to upgrade existing PABX to VoIP calls. No need to expand your PABX’s extension
olines and analog trunk lines.


 

Specification

  • Interface :
    • Ethernet port (RJ-45, 10/100 base-T)
    • 1-WAN port, connect to IP Network
    • 1-LAN port connect to PC with NAT
    • Support Bridge, NAT and Gateway mode
    • Telephony port connect to local analog line (RJ-11 x 8 pcs)
    • DC +12V power input Jack
    • LED Indicator for System, SIP, and FXS status
  • IP Network connection :
    • IPv4 (RFC 791) and IPv6 Simultaneously
    • IPv6 Auto Configuration (RFC 4862)
    • IPv6 Only, IPv4 Only or dual stack
    • MAC Address (IEEE 802.3)
    • MAC Clone Setting
    • Vendor Class ID
    • IP/ICMP/ARP/RARP/SNTP
    • Static IP
    • DHCP Client (RFC 2131), WAN port
    • DHCP Server, LAN port
    • NAT Server (RFC 1631)
    • PPPoE Client
    • DDNS (DynDNS )
    • DNS Client
    • Firewall
    • URL Filter
    • IP Filter
    • MAC Address Filter
    • Application program Filter
    • Port Filter
    • Port Forwarding (TCP, UDP or both)
    • Bandwidth Control (Download and Upload),
      Maximum Bandwidth priority setting
    • UPnP Server at LAN port
    • Behind NAT, use DMZ for NAT traversal
    • SNTP with time zone and Daylight Saving
    • TCP/UDP (RFC 793/768)
    • RTP/RTCP (RFC 1889/1890)
    • IPV4 ICMP (RFC 792),
    • TFTP Client
    • VoIP VLAN Support 802.1Q, 802.1P
    • VLAN ID Range : 2 to 4094
    • VLAN Priority : 0 to 7 (Highest Priority)
    • QoS : DiffServ (RFC 2475), TOS (RFC791, 1394)
  • SIP Protocol :
    • RFC3261 compliance
    • Support up-to 16 SIP Trunk to Register
    • SIP UDP Protocol
    • Support SIP compact Form
    • Support SIP HOLD Type: Send Only, 0.0.0.0 or inactive
    • SIP Session Timer (RFC 4028)
    • SIP Session Refresher: UAC or UAS
    • SIP Encryption
    • MD5 Digest Authentication (RFC2069/RFC2617)
    • Reliability of provision response PRACK (RFC3262)
    • Early/Delay Media support
    • Offer/Answer (RFC3264)
    • Message Waiting Indication (RFC3842)
    • Event Notification (RFC3265)
    • REFER (RFC3515)
    • Support Outbound Proxy
    • Support Primary and Backup SIP Server
    • Support STUN NAT Traversal
    • Support “rport” parameter (RFC 3581)
    • Configure SIP local Port
    • SIP QoS Type: DiffServe or QoS
    • Accept Proxy Only : YES or NO
  • Audio Codec :
    • G.711 A-law/μ-law, G.729A, GSMFR, G.723.1(6.3K, 5.3K)
    • Select voice codec priority: According to Local or Remote
    • Voice Payload size (ms) configuration
    • Silence Suppression
    • VAD/CNG
    • LEC : Line Echo Canceller
    • Max Echo Tail Length (G.168): 32, 64 and 128ms
    • Packet Loss Compensation
    • Automatic Gain Control
    • In-band/out of band DTMF (RFC4733, RFC2833 / SIP INFO)
    • Adaptive/Configurable Jitter Buffer
    • G.168 Acoustic Echo Cancellation
    • Configure RTP basic Port
    • RTP QoS Type : DiffServ or TOS
    • Phone Book (50 records) for peer to peer calls
    • Dialing Plan with drop, replace, Insert dialing digits
    • Select First digit and Inter digit timeout duration (Sec)
    • Selectable Call Progress Tone
    • Support Specified Line Calling
  • Call Features :
    • Support Peer to Peer Dialing
    • Up to 8-port FXS connects to analog phone set or analog trunk of PBX.
    • Caller ID generates DTMF (before/after 1st ring) and FSK (before 1st ring ),
      ETSI and Bellcore
    • DTMF Caller ID start and stop BIT configurable
    • Current Drop generation to FXS analog devices
    • Disconnect tone generation
    • Tone Generation: Ring Back, Dial, Busy, call waiting, ROH, Warning, Holding,
      Stutter dial tone and disconnect tone
    • Configure Tone Frequency, Cadence, Level and Cycle
    • Select Tone specification by Country name List
    • Global Country Based Tone Specification
    • NAT Traversal support STUN, UPNP and Behind NAT
    • Out-Band DTMF : RFC2833 and SIP Info
    • RFC2833 Payload type : 101 or 96
    • DTMF send out ON and OFF Time configure
    • DTMF incoming recognition Minimum ON and OFF time
    • DTMF Relay Volume configuration
    • T.38 FAX Volume configuration
    • Flash Time transmit via SIP Info (Enable or Disable)
    • Message Waiting Indication (Stutter Tone Notice)
    • Block Anonymous Call
    • Call Hold
    • Call Transfer
  • FXS Line Configuration :
    • Activate or deactivate
    • Line ID
    • Line Phone number
    • Polarity Reversal generation for call establish and Billing.
    • Current drop generation to release line
    • Incoming call Handle: Hotline or 2 stage dialing
    • HOT Line to desired phone number
    • Recognize FLASH TIME from analog device
    • T.38 or FAX Relay Type
    • Incoming and outgoing volume in dB configurable
    • Dialing Answer Delay time to establish call path
    • Caller ID generation mode by Country selection
    • Outgoing SIP Caller ID Selection
    • Support 16 SIP Trunk
    • Accept desired SIP Proxy incoming calls Only (Avoid hacker’s call)
  • Flexible Routing Plan :
    • Prefix Match and Length
    • Priority Ring
    • Cyclic Ring
    • Simultaneous Ring
    • Programmable Hunting Cycle
    • Backup Routes with Digit Manipulation
    • Default Routes
  • Flexible Dial Plans :
    • Retrieve transfer call from 3rd party by dial Code (default: *#)
    • Inter digit time out setting
    • First digit dial out delay time setting
    • End of dial keypad number
    • Dial Rule : Match dial Prefix and Maximum digits length ( 1-15 )
    • Phone Book can be Exported or Imported
  • Digit Manipulation (Drop and Replace Rule) :
    • FXS DM Group
    • VoIP DM Group
      DM 1 Group
      DM 2 Group
      DM 3 Group
      DM 4 Group
    • Matched Prefix
    • Matched digit length
    • Replace digit start position
    • Replace digit stop position
    • Replace number
  • FXS Analog 2-wire interface :
    • Flash Time Detection: range from 80 to 800 ms
    • ON-HOOK Voltage -48Vdc
    • Configure Ring Cadence, Frequency and Voltage
    • Support Polarity reversal to start Billing
    • Service Up to 1 Kilo-meter distance to analog telephone set
    • Generate Current Drop Time (Open Loop Disconnect time)
  • MANAGEMENT :
    • Administrative Telnet CLI and HTTP, HTTPS
    • HTTP provision through MAC address
    • Multilingual Web User Interface
    • 3 Levels of User Access Authority with Password protection with
      different Web Language (Administrator, Supervisor and User)
    • HTTP/HTTPS Service Access limitation from WAN port
    • Configure Service ports at HTTP, HTTPS and Telnet Services
    • Phone Debug Module: Device Control, Call Control, DB, Verbose
    • SIP Debug Module: Register, Call, SIP Message, Others
    • SNTP Debug Module
    • Device Debug Module
    • DSP Debug
    • Provide 8 Debug Levels:
      Emergency
      Alert
      Critical
      Error
      Warning
      Notice
      Information
      Debug
    • Provides System Status Logs
    • Connect to external SYSLOG Server
    • Status display: Network, Line, SIP Trunk status
    • Diagnostics (debug through Syslog Event Notice)
    • Debug in real time by Telnet
    • Auto Provision via HTTP Server
    • SNMP V2/Trap
    • Configuration Backup/Restore
    • Dual Firmware Image Backup
  • Environmental :
    • Physical Dimension: 44(w) x 4.5(h) x 11(d) CM.
    • Weight: 2.3kg (One unit with packing)
    • Operating Temp. & Humidity
      • Temp.: 0°C~45°C (32°F~113°F)
      • Humidity: 10%~90% relative humidity, non-condensing
    • Maximum Power Consumption: 17 Watts (1.5A at 12Vdc)
    • Power Adaptor:
      • INPUT: AC100V~240V, 50/60Hz
      • OUTPUT: DC 12V, 3A
  • Approvals :
    • CE, FCC (Part 15, Class B), LVD and RoHS
  • Country of origin :
    • Made in Taiwan
  • Packing Accessories
    • WellGate 2808 main unit          x 1 pcs
    • AC to DC+12V/3A Power adaptor    x 1 pcs
    • Rack Mount bracket                        x 2 pcs
  • Warranty
    • One year

 


 

Copyright © 2015. WELLTECH TECHNOLOGY CO., LTD. All Rights Reserved.