Update WG3806 in boot mode Procedures

Prepare the following before You starting.
- Turn OFF Wellgate 3806
- Connect console port cable from WG3806 to PC
- Connect WG3806 and PC to an local LAN
- Install tftp program to your PC and activated the tftp program
- Put download file (i.e. 2MWG3806.111) and tftp program at the same directory in your PC
- Activate HyperTerminal program from your PC
 
Now, Turn ON power supply of Wellgate 3806. You will see the following display from HyperTerminal display of your PC.
 
Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
Please wait while system is initializing ..........         ----> press enter within 3 seconds. 
 
Now it is in BOOT MODE. 
 
boot line : cpm(0,0)host:vxWorks h=192.168.4.109 e=192.168.201.201 u=vwusr pw=vw
usr g=192.168.1.254

login    : water

password : 3333
 
[help] , list all boot commands
 
1. [c] 
<BOOT> c
- Please input your new network address.    ----> for example,
- Tftp server addr: 192.168.4.109           ----> prepare one tftp server
- Target addr: 192.168.119.119              ----> given one IP address for the Wellgate 3806 
- Gateway addr: 192.168.1.254               ----> default network gateway ip address
- user (u):                                 ----> key in any number 
- ftp password (pw):                        ----> key in any number 
- netmask :                                 ----> key in any number 
 
 
- if network address is correct, please press 'y' to
  setup configuration, else press 'n' to continue.          ----->  y
 
 bootline configuraton OK.
- auto reset
Starting at 0x2800100...
 
Attached TCP/IP interface to cpm unit 0                     -----> again
Attaching interface lo0...done
Please wait while system is initializing ..........         -----> press enter within 3 seconds. 

Key in Login and password as above. 
 
Note, all IP Address must be in the same subnet mask and default gateway.  
 
2. [f]
 
<BOOT> f
- Transfer File Name: 2mwt3806 .111        ----> example , file to be download 
 
3. [d]
 
<BOOT> d
- download program.
- Load ....
Tftp transfer OK.
 
Note: if it is not successful, try to change another IP Address for Wellgate 3806 at  - Target addr: 192.168.119.119 and repeat step 1 again.        
 
4. [z]
             
<BOOT> z
- programming 2M rom file

- Be sure to program boot sector!!?(y/n):y              --------> press y

    Please wait for a moment!!!
- programming OK.
 
 
5. [r]
<BOOT> r
- software reset
Starting at 0x2800100...
 
After download is finished, all the settings will return to default values including IP 
address (default IP address is 10.1.1.3) and MAC address, so please re-configure IP address 
and MAC address and reboot it.

Configure the MAC address with the command 

setmac
(Note: Each network device MUST has an unique mac address which are 12 digits length. The H.323 gateway has to re-configure an unique mac address after this upgrade procedure. An unproper operation may be happened if mac address is duplicated with other network device.) 

key in mac address with format:    00
                              01
                              a8
                              00
                              0x
                              xx
    (It means to press enter key each time after key in two characters.)
You can find the device MAC address from the label which is located at the bottom of Wellgate 3806 metal case. Now, give the following two commands.

flash -clean
reboot
 
Now, you can start to configure your setting on Wellgate 3806.